Difference between revisions of "Laser training"

From BloomingLabs
Jump to: navigation, search
Line 12: Line 12:
  
 
If your job catches on fire:
 
If your job catches on fire:
*You are more important than the laser--do not put yourself in unnecessary danger to save the laser. (Cf. Bloominglabs rules)
+
* You are more important than the laser--do not put yourself in unnecessary danger to save the laser. (Cf. Bloominglabs rules)
*Use your judgment--flare-ups will happen, and most go out quickly (a second or so) on their own.
+
* Use your judgment--flare-ups will happen, and most go out quickly (a second or so) on their own.
*Any flame lasting longer than a second or two is a fire--put it out.
+
* Any flame lasting longer than a second or two is a fire--put it out.
  
 
===Eye safety===
 
===Eye safety===
Line 29: Line 29:
 
=== Quick Start ===
 
=== Quick Start ===
 
* Turn on main power strip
 
* Turn on main power strip
* Verify water pump and ventilation fan are running
+
* Verify water pump is pumping water (you should be able to feel the flow in either hose)
 +
* Verify ventilation fan, and air assist compressor are running
 
* Make sure print area is clear and clean
 
* Make sure print area is clear and clean
 
* Start/attach dedicated computer and start up RetinaEngrave
 
* Start/attach dedicated computer and start up RetinaEngrave
 +
* Home lens head by using home button on device or pressing 'H' in RetinaEngrave
 
* Place material to be cut/etched on honeycomb
 
* Place material to be cut/etched on honeycomb
 
* Close lid, holding it at the middle so it doesn't catch in the back
 
* Close lid, holding it at the middle so it doesn't catch in the back

Revision as of 09:24, 8 May 2013

Page for getting folks up to speed on the laser.


Contents

Safety

Don't cut anything particularly flammable or noxious. Check the Laser Infobase page for this list

Fire

When using the laser, whether for engraving or cutting, stay and watch your job.

Know where the fire extinguisher is and be ready to use it.

If your job catches on fire:

  • You are more important than the laser--do not put yourself in unnecessary danger to save the laser. (Cf. Bloominglabs rules)
  • Use your judgment--flare-ups will happen, and most go out quickly (a second or so) on their own.
  • Any flame lasting longer than a second or two is a fire--put it out.

Eye safety

Do not look directly into either the cutting laser or even the visible targeting laser.

Make sure the lid is down before you even try starting your job. There is an integrated safety lock-out, but don't rely on this.

The lid should absorb most laser radiation, but if you're cutting reflective material, it wouldn't hurt to use the tinted safety glasses (should be located near the laser).

Operation

Always make sure the water pump is working and that there's plenty of water in the reservoir (blue bucket below the blower and compressor). Operating the laser without the cooling system running will damage it.

Quick Start

  • Turn on main power strip
  • Verify water pump is pumping water (you should be able to feel the flow in either hose)
  • Verify ventilation fan, and air assist compressor are running
  • Make sure print area is clear and clean
  • Start/attach dedicated computer and start up RetinaEngrave
  • Home lens head by using home button on device or pressing 'H' in RetinaEngrave
  • Place material to be cut/etched on honeycomb
  • Close lid, holding it at the middle so it doesn't catch in the back
  • Move lens head to top left of desired print area using either onboard or RetinaEngrave controls
  • Adjust speed and power to appropriate levels for material and job
  • Run raster portion before vector
  • Watch your job like a hawk
  • Allow the blower to clear any remaining smoke before opening the lid
  • Remove your engraved/cut object!


Additional Tips

  • For higher precision placement of the lens (say, for engraving on small objects) hit the padlock button on the control panel until it says "Unlocked", then use your hands to carefully move the lens to the correct starting location. There's no need to relock the lens position when you are done, just start the operation.

Additional lenses

Using the removable bottom

Personal tools